My New Combo

Shortblock
	<a href="http://www.keithcraft.com">Keith Craft Racing</a> 306 c.i. Stock 
		$1649 retail price
	Seasoned Block bored 0.030 over
		Deck Height (#1-8) 0.004, 0.003, 0.004, 0.005, 0.000, 0.002, 0.003, 0.003
	Stock Crank
		2.247-3/4" Main Journals
		2.250-1/2" Bearing Bore
		0.002-3/4" Clearance
		0.004" Endplay
		0.020-0.022" Side Clearance
	Eagle I-Beam Connecting Rods
		Not part of Stock kit - I added them for $100 extra
		0.912" Pin Size
		2.112-3/4" Rod Journals
		2.115-3/4" Bearing Bore
		0.003" Clearance
	TRW Flat Top, 4 valve relief, Forged Pistons 
		L2482 .030 2F059
		Pistons were flycut to drop compression to ~9.0 with 60cc heads
	Childs & Albert Plasma Moly Rings 
		5/64", 5/64", 3/16" ring thickness
		0.18" top ring gap, 0.017" second ring gap
		Part Number RS9902 (4.030 bore)
	ARP Main Studs (standard 302)
	ARP Rod Bolts (standard 302)
	Machine Work
		All was balanced and blueprinted (50 oz)
		Block was bored and honed with torque plates
		Mock up square deck
	Federal Mogul Main Bearings
		4125M
	Federal Mogul Rod Bearings
		8-2600CP
	Federal Mogul Cam Bearings
		1204M
	FMS Double Roller Timing Set
		M-6268-A302
		Add $59 since I didn't get a cam
	Stock 1995 GT cam
		Subtract $200 for no cam in Kit
	Total Cost was $1608 plus $115 Residential Truck Freight

Accessories
	NAPA Water Pump
		Part # ????????????????????
	Stock A/C, Alternator, Power Steering, Air Pump, etc.

Heads and Valve Train
	Edelbrock Performer 5.0 Aluminum Heads - Assembled
		$975 from Keith Craft (shipped with Shortblock)
		Part #6037
		Pedastal Mount
	Stock Roller Lifters
	Stock Push Rods
	Stock Pedastals
	1.7:1 ROCKERS??????????????????
	ARP Head Bolts
		PART NUMBER???????????
	Edelbrock Head Bolt Bushings
		PART NUMBER????????????
	Fel-Pro  ????????????   Head Gaskets

Induction and Supercharger
	Kenne Bell Conical (K&N type) Filter
	Home Depot Stove Pipe Elbow to put filter in fender
	Kenne Bell/Ford 80mm Mass Air Sensor (MAS)
	Stock "Plumbing"
	Stock 1995 60mm Throttle Body and Electronics
	Kenne Bell Supplied Intake Elbow
	Kenne Bell 1500 "Whipplecharger" Supercharger
	2-3/8" Blower Pulley (approx 10 psi)
	Stock Crank Pulley
	Stock 1995 GT Lower Intake Manifold
	Fel-Pro 1262 Lower Intake Manifold Gaskets??????????????

DriveTrain
	Stock Harmonic Balancer???????????????
	Flywheel?????????????????????????????
	Clutch?????????????????????????
	Pressure Plate??????????????????
	Throwout Bearing?????????????????
	Clutch Quadrant and Cable?????????
	Stock T5 Transmission
	Stock Driveshaft
	Lakewood/FMS Driveshaft Safety Loop
	
Rear Assembly
	Stock 8.8" Housing
	Stock 2.73:1 Gears
	Stock 28 spline axles
	Stock Wheel Studs